1
Simulateurs / L2M2 Problems
« le: Mardi 17 Septembre 2013, 18:36:44 pm »
Here are some hi-res photos of my PCB
Sorry, I cant work out how to make them thumbnails!
Sorry, I cant work out how to make them thumbnails!
L'Arcade sous toutes ses formes !
Nouvelles:
Besoin de contacter un admin pour une proposition, une suggestion ou discuter d'un probleme ?
C'est ici : Misteriddler, AsPiC ou Pich
Voir les contributions
Cette section vous permet de consulter les contributions (messages, sujets et fichiers joints) d'un utilisateur. Vous ne pourrez voir que les contributions des zones auxquelles vous avez accès.
Pages: [1]
2
Simulateurs / L2M2 Problems
« le: Mardi 17 Septembre 2013, 17:46:54 pm »
Ok I have replaced LM324 and things are now working. The CW and the CCW LEDs are responding when I try out the force feedback effects.
My final problem is that my electricity keeps on blowing, every time I plug in my L2M2 the lights in the house dim and sometimes the electricity fuse blows.
Something is obviously very wrong with the board, any suggestions where to look?
My final problem is that my electricity keeps on blowing, every time I plug in my L2M2 the lights in the house dim and sometimes the electricity fuse blows.
Something is obviously very wrong with the board, any suggestions where to look?
3
Simulateurs / L2M2 Problems
« le: Lundi 16 Septembre 2013, 20:39:57 pm »
ok new logitech wheels have arrived, I have tested all my voltages on the L2M2 PCB and they are as follows...
RV5 and RV1 = 20 V
RV2 and RV3 = 12.5 V
The CW LED correctly flashes but the CCW LED at D3 is constantly lit. Any ideas where to start troubleshooting?
RV5 and RV1 = 20 V
RV2 and RV3 = 12.5 V
The CW LED correctly flashes but the CCW LED at D3 is constantly lit. Any ideas where to start troubleshooting?
4
Simulateurs / L2M2 Problems
« le: Vendredi 13 Septembre 2013, 15:02:51 pm »
I have purchased some new logitech wheels so just waiting for them to arrive. Would be nice to be able to resurrect these broken pcbs though 
I am going to check the L2M2 board first before I plug any of my new wheels into it, hopefully prevent any more blowouts
I am going to check the L2M2 board first before I plug any of my new wheels into it, hopefully prevent any more blowouts
5
Simulateurs / L2M2 Problems
« le: Jeudi 12 Septembre 2013, 20:09:46 pm »
I have not got an oscilloscope unfortunately 
If I do find the pin on the ST micro-controller, can the signal be used?
If I do find the pin on the ST micro-controller, can the signal be used?
6
Simulateurs / L2M2 Problems
« le: Jeudi 12 Septembre 2013, 18:08:38 pm »
I did not check the functioning of the L2M2 before I connected to Logitech board, my mistake really.
In a previous post you said....
'Pour ta carte logitech brulé, ne l'a jette pas. Je pense que seul le pont en H est mort, tu pourra récupérer le signal directement en sortie du microcontrolleur ST (j'ai oublié quelle patte mais on l'a retrouve vite avec un oscillo)'
Can you explain what you meant?
In a previous post you said....
'Pour ta carte logitech brulé, ne l'a jette pas. Je pense que seul le pont en H est mort, tu pourra récupérer le signal directement en sortie du microcontrolleur ST (j'ai oublié quelle patte mais on l'a retrouve vite avec un oscillo)'
Can you explain what you meant?
7
Simulateurs / L2M2 Problems
« le: Jeudi 12 Septembre 2013, 12:48:12 pm »
Thanks for the clarification
I followed the schematics listed at http://www.gamoover.net/tuto/l2m2-interfacer-un-ffb-et-volant-sega-model-12-avec-un-pc-ou-une-playstation-23 exactly and used the LM324 op-amp
The motor controller on the Logitech board is receiving the FFB commands but is not outputting them since I connected it to the L2M2.
Can the L2M2 use the FFB signals from the motor controller input instead of the output?
I followed the schematics listed at http://www.gamoover.net/tuto/l2m2-interfacer-un-ffb-et-volant-sega-model-12-avec-un-pc-ou-une-playstation-23 exactly and used the LM324 op-amp
The motor controller on the Logitech board is receiving the FFB commands but is not outputting them since I connected it to the L2M2.
Can the L2M2 use the FFB signals from the motor controller input instead of the output?
8
Simulateurs / L2M2 Problems
« le: Jeudi 12 Septembre 2013, 10:07:03 am »
Sorry, I really dont understand what you mean. Google translate isn't making any sense of your replay. Can you write it more simply?
9
Simulateurs / L2M2 Problems
« le: Jeudi 12 Septembre 2013, 01:15:58 am »
Hi all, apologies for the post in English but I don't speak French
I have built the L2M2 board but every time I connect a Logitech PCB to E1 and E2 the Force Feedback stops working completely. I have destroyed 4 Logitech PCBs so far!
I have measured the voltage on pin 7 (phase) of the Logitech PCB Motor Controller and it does fluctuate when I test the FFB.
Is there a way I can tap into this signal and connect to the L2M2?
I have built the L2M2 board but every time I connect a Logitech PCB to E1 and E2 the Force Feedback stops working completely. I have destroyed 4 Logitech PCBs so far!
I have measured the voltage on pin 7 (phase) of the Logitech PCB Motor Controller and it does fluctuate when I test the FFB.
Is there a way I can tap into this signal and connect to the L2M2?
Pages: [1]